.. zephyr:board:: blackpill_f401cc

Overview

The WeAct Black Pill V1.2 Board is an extremely low cost and bare-bones development board featuring the STM32F401CC, see STM32F401CC website. This is the 48-pin variant of the STM32F401x series, see STM32F401x reference manual. More info about the board available here <stm32-base-board-page_>_ and on WeAct Github_.

Hardware

The STM32F401CC based Black Pill V3.0+ Board provides the following hardware components:

STM32F401CCU6 in UFQFPN48 package
ARM® 32-bit Cortex®-M4 CPU with FPU
84 MHz max CPU frequency
VDD from 1.7 V to 3.6 V
256 KB Flash
64 KB SRAM
GPIO with external interrupt capability
1x12-bit, 2.4 MSPS ADC with 16 channels
DMA Controller
Up to 11 Timers (six 16-bit, two 32-bit, two watchdog timers and a SysTick timer)
USART/UART (3)
I2C (3)
SPI/I2S (5)
SDIO
USB 2.0 full-speed device/host/OTG controller with on-chip PHY
CRC calculation unit
96-bit unique ID
RTC

Supported Features

.. zephyr:board-supported-hw::

Pin Mapping

Available pins:

.. image:: img/Blackpill_Pinout.jpg :align: center :alt: Black Pill V1.2 Pinout

Default Zephyr Peripheral Mapping:

UART_1 TX/RX : PA9/PA10
I2C1 SCL/SDA : PB8/PB9
SPI1 CS/SCK/MISO/MOSI : PA4/PA5/PA6/PA7 (Routed to footprint for external flash)
PWM_4_CH1 : PB6
PWM_4_CH2 : PB7
ADC_1 : PA1
USER_PB : PA0
USER_LED : PC13

Clock Sources

The board has two external oscillators. The frequency of the slow clock (LSE) is 32.768 kHz. The frequency of the main clock (HSE) is 25 MHz.

The default configuration sources the system clock from the PLL, which is derived from HSE, and is set at 84MHz, which is the maximum possible frequency to achieve a stable USB clock (42MHz).

Programming and Debugging

.. zephyr:board-supported-runners::

There are 2 main entry points for flashing STM32F4X SoCs, one using the ROM bootloader, and another by using the SWD debug port (which requires additional hardware). Flashing using the ROM bootloader requires a special activation pattern, which can be triggered by using the BOOT0 pin.

Flashing

Installing dfu-util

It is recommended to use at least v0.8 of dfu-util_. The package available in debian/ubuntu can be quite old, so you might have to build dfu-util from source.

There is also a Windows version which works, but you may have to install the right USB drivers with a tool like Zadig_.

Flashing an Application

Connect a USB-C cable and the board should power ON. Force the board into DFU mode by keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.

The dfu-util runner is supported on this board and so a sample can be built and tested easily.

.. zephyr-app-commands:: :zephyr-app: samples/basic/blinky :board: blackpill_f401cc :goals: build flash

Debugging

The board can be debugged by installing the included 100 mil (0.1 inch) header, and attaching an SWD debugger to the 3V3 (3.3V), GND, SCK, and DIO pins on that header.

References

.. target-notes::

.. _board release notes: https://github.com/WeActStudio/WeActStudio.MiniSTM32F4x1/blob/master/HDK/README.md

.. _Zadig: https://zadig.akeo.ie/

.. _WeAct Github: https://github.com/WeActStudio/WeActStudio.MiniSTM32F4x1

.. _stm32-base-board-page: https://stm32-base.org/boards/STM32F401CCU6-WeAct-Black-Pill-V1.2.html

.. _dfu-util: http://dfu-util.sourceforge.net/build.html

.. _STM32F401CC website: https://www.st.com/en/microcontrollers/stm32f401cc.html

.. _STM32F401x reference manual: https://www.st.com/resource/en/reference_manual/dm00096844.pdf