boards/shields/arducam_cu450_ov5640/doc/index.rst
.. _arducam_cu450_ov5640:
ArduCam CU450 OV5640 Camera Module ##################################
Overview
The ArduCam CU450 OV5640 shield provides the OV5640 image sensor on a 40-pin FFC connector,
supporting both the DVP (Digital Video Port) interface and the MIPI CSI-2 interface.
It is designed specifically for the Renesas EK-RA8P1_ evaluation kit.
+-----+----------------------+ | Pin | Function | +=====+======================+ | 1 | GND | +-----+----------------------+ | 2 | D11 | +-----+----------------------+ | 3 | D10 | +-----+----------------------+ | 4 | GND | +-----+----------------------+ | 5 | D9 / MIPI_CSI2_DL1_P | +-----+----------------------+ | 6 | D8 / MIPI_CSI2_DL1_N | +-----+----------------------+ | 7 | GND | +-----+----------------------+ | 8 | D7 / MIPI_CSI2_CL1_P | +-----+----------------------+ | 9 | D6 / MIPI_CSI2_CL1_N | +-----+----------------------+ | 10 | GND | +-----+----------------------+ | 11 | D5 / MIPI_CSI2_DL0_P | +-----+----------------------+ | 12 | D4 / MIPI_CSI2_DL0_N | +-----+----------------------+ | 13 | GND | +-----+----------------------+ | 14 | D3 | +-----+----------------------+ | 15 | D2 | +-----+----------------------+ | 16 | GND | +-----+----------------------+ | 17 | D1 | +-----+----------------------+ | 18 | D0 | +-----+----------------------+ | 19 | GND | +-----+----------------------+ | 20 | SCL | +-----+----------------------+ | 21 | SDA | +-----+----------------------+ | 22 | GND | +-----+----------------------+ | 23 | VSYNC | +-----+----------------------+ | 24 | HSYNC | +-----+----------------------+ | 25 | RESET | +-----+----------------------+ | 26 | XCLK | +-----+----------------------+ | 27 | PCLK | +-----+----------------------+ | 28 | INT | +-----+----------------------+ | 29 | GND | +-----+----------------------+ | 30 | GND | +-----+----------------------+ | 31 | 3V3 | +-----+----------------------+ | 32 | GND | +-----+----------------------+ | 33 | GND | +-----+----------------------+ | 34 | 3V3 | +-----+----------------------+ | 35 | 3V3 | +-----+----------------------+ | 36 | 3V3 | +-----+----------------------+ | 37 | GND | +-----+----------------------+ | 38 | GND | +-----+----------------------+ | 39 | 3V3 | +-----+----------------------+ | 40 | GND | +-----+----------------------+
Requirements
This shield requires a board with a 40-pin FFC connector. The Renesas EK-RA8P1 evaluation kit is fully supported.
.. note:: While the CU450 OV5640 module and connector provide both DVP and MIPI CSI-2 interfaces, only the DVP interface is currently supported on Renesas RA SoCs. MIPI CSI-2 is not yet supported on this platform.
Programming
Set --shield arducam_cu450_ov5640_dvp when you invoke west build. For example:
.. zephyr-app-commands:: :zephyr-app: samples/drivers/video/capture :board: ek_ra8p1/r7ka8p1kflcac/cm85 :shield: arducam_cu450_ov5640_dvp :goals: build
References
.. target-notes::
.. _EK-RA8P1: https://www.renesas.com/en/design-resources/boards-kits/ek-ra8p1/