.. zephyr:board:: warp7

Overview

The i.MX7S SoC is a Hybrid multi-core processor composed of Single Cortex A7 core and Single Cortex M4 core. Zephyr was ported to run on the M4 core. In a later release, it will also communicate with the A7 core (running Linux) via RPmsg.

Hardware

The WaRP7 Platform is composed of a CPU and IO board.

WaRP7 IO Board

6-axis Accelerometer Magnetometer: NXP FXOS8700CQ (I2C4 interface)
3-axis Gyroscope: NXP FXAS21002C (I2C4 interface)
Altimeter: NXP MPL3115A2 (I2C4 interface)
NXP NTAG NT3H1101 (I2C2 interface)
Audio Codec: NXP SGTL5000 (I2C4 and SAI1 interfaces)
S1 - Reset Button (POR_B signal)
S2 - User Defined button (ENET1_RD1/GPIO7_IO1 signal)
S3 - On/Off (MX7_ONOFF signal)
Board to board connector (34 configurable pins)
mikroBUS expansion connector
10-pin needle JTAG Connector
Debug USB exposing two UARTs (UART1 for A7 and UART2 for M4)
MIPI DSI 1 lane Connector
LCD Touch Connector (I2C2 interface)
Audio Jack: Mic and Stereo Headphone

WaRP7 CPU Board

CPU i.MX7 Solo with a Single Cortex A7 (800MHz) core and Single Cortex M4 (200MHz) core
Memory
- RAM -> A7: 4GB (Kingston 08EMCP04)
- RAM -> M4: 3x32KB (TCML, TCMU, OCRAM_S), 1x128KB (OCRAM) and 1x256MB (DDR)
- Flash -> A7: 8GB eMMC (Kingston 08EMCP04)
Multimedia
- MIPI CSI 1 lane connector with 5MP OV5640 camera module (I2C2 interface)
Connectivity
- Board to board connector (34 configurable pins)
- Micro USB 2.0 OTG connector (USB_OTG1 interface)
- Murata Type 1DX Wi-Fi IEEE 802.11b/g/n and Bluetooth 4.1 plus EDR (SD1, UART3 SAI2 interfaces)
Li-ion/Li-polymer Battery Charger: NXP BC3770 (I2C1 interface)
Power management integrated circuit (PMIC): NXP PF3000 (I2C1 interface)

For more information about the i.MX7 SoC and WaRP7, see these references:

i.MX 7 Series Website_
i.MX 7 Solo Datasheet_
i.MX 7 Solo Reference Manual_
WaRP7 Site_
WaRP7 Quick Start Guide_
WaRP7 User Guide_
WaRP7 GitHub repository_

Supported Features

.. zephyr:board-supported-hw::

Connections and IOs

The WaRP7 board Board was tested with the following pinmux controller configuration.

System Clock

The M4 Core is configured to run at a 200 MHz clock speed.

Serial Port

The iMX7S SoC has seven UARTs. The number 2 is configured for the console and the number 6 is used in the mikroBUS connector.

Programming and Debugging

.. zephyr:board-supported-runners::

The WaRP7 doesn't have QSPI flash for the M4 and it needs to be started by the A7 core. The A7 core is responsible to load the M4 binary application into the RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer, and get the M4 out of reset. The A7 can perform these steps at bootloader level or after the Linux system has booted.

The M4 can use up to 5 different RAMs. These are the memory mapping for A7 and M4:

References

i.MX 7 Solo Reference Manual_ from page 182 (section 2.1.2 and 2.1.3)
Toradex Wiki_

At compilation time you have to choose which RAM will be used. This configuration is done in the file :zephyr_file:boards/element14/warp7/warp7_mcimx7d_m4.dts with "zephyr,flash" (when CONFIG_XIP=y) and "zephyr,sram" properties. The available configurations are:

.. code-block:: none

"zephyr,flash"

&ddr_code
&tcml_code
&ocram_code
&ocram_s_code
&ocram_pxp_code
&ocram_epdc_code

"zephyr,sram"

&ddr_sys
&tcmu_sys
&ocram_sys
&ocram_s_sys
&ocram_pxp_sys
&ocram_epdc_sys

Below you will find the instructions to load and run Zephyr on M4 from A7 using u-boot.

Connect both micro USB interfaces into the PC. In one USB interface you will have 2 USB serial ports, the first one is the A7 console and the second is the M4 console for Zephyr with both configured to work at 115200 8N1. The other USB interface is used to power the CPU and IO boards and is connected to the USB OTG interface of the i.MX7S.

After powering up the platform stop the u-boot execution on the A7 core and expose the eMMC as mass storage with the following command in the u-boot prompt: ums 0 mmc 0. Copy the compiled zephyr.bin to the first FAT partition and remove the mounted device on the PC by issuing a "Ctrl+C" in the u-boot prompt. Set the u-boot environment variables and run the zephyr.bin from the appropriated memory configured in the Zephyr compilation:

.. code-block:: console

setenv bootm4 'fatload mmc 0:1 $m4addr $m4fw && dcache flush && bootaux $m4addr'

TCML

setenv m4tcml 'setenv m4fw zephyr.bin; setenv m4addr 0x007F8000' setenv bootm4tcml 'run m4tcml && run bootm4' run bootm4tcml

TCMU

setenv m4tcmu 'setenv m4fw zephyr.bin; setenv m4addr 0x00800000' setenv bootm4tcmu 'run m4tcmu && run bootm4' run bootm4tcmu

OCRAM

setenv m4ocram 'setenv m4fw zephyr.bin; setenv m4addr 0x00900000' setenv bootm4ocram 'run m4ocram && run bootm4' run bootm4ocram

OCRAM_S

setenv m4ocrams 'setenv m4fw zephyr.bin; setenv m4addr 0x00180000' setenv bootm4ocrams 'run m4ocrams && run bootm4' run bootm4ocrams

DDR

setenv m4ddr 'setenv m4fw zephyr.bin; setenv m4addr 0x80000000' setenv bootm4ddr 'run m4ddr && run bootm4' run bootm4ddr

Debugging

Download and install J-Link Tools_ and NXP iMX7D Connect CortexM4.JLinkScript_.

To run Zephyr Binary using J-Link, create the following script to get the Program Counter and Stack Pointer from zephyr.bin.

get-pc-sp.sh: .. code-block:: console

#!/bin/sh

firmware=$1

pc=$(od -An -N 8 -t x4 $firmware | awk '{print $2;}') sp=$(od -An -N 8 -t x4 $firmware | awk '{print $1;}')

echo pc=$pc echo sp=$sp

Get the SP and PC from firmware binary: ./get-pc-sp.sh zephyr.bin .. code-block:: console

pc=00900f01 sp=00905020

Plug in the J-Link into the board and PC and run the J-Link command line tool:

.. code-block:: console

/usr/bin/JLinkExe -device Cortex-M4 -if JTAG
-speed 4000 -autoconnect 1 -jtagconf -1,-1
-jlinkscriptfile iMX7D_Connect_CortexM4.JLinkScript

The following steps are necessary to run the zephyr.bin:

Put the M4 core in reset
Load the binary in the appropriate addr (TMCL, TCMU, OCRAM, OCRAM_S or DDR)
Set PC (Program Counter)
Set SP (Stack Pointer)
Get the M4 core out of reset

Issue the following commands inside J-Link commander:

.. code-block:: console

w4 0x3039000C 0xAC loadfile zephyr.bin,0x00900000 w4 0x00180000 00900f01 w4 0x00180004 00905020 w4 0x3039000C 0xAA

With these mechanisms, applications for the warp7 board configuration can be built and debugged in the usual way (see :ref:build_an_application and :ref:application_run for more details).

References

Loading Code on Cortex-M4 from Linux for the i.MX 6SoloX and i.MX 7Dual/7Solo Application Processors_
J-Link iMX7D Instructions_

.. _WaRP7 Site: https://www.element14.com/warp7

.. _WaRP7 User Guide: https://github.com/WaRP7/WaRP7-User-Guide/releases/download/v1.3/User_Guide_Manual_v1-3.pdf

.. _WaRP7 Quick Start Guide: https://www.nxp.com/docs/en/supporting-information/WARP7-LEAFLET-QSG.pdf

.. _WaRP7 GitHub repository: https://github.com/WaRP7

.. _i.MX 7 Series Website: https://www.nxp.com/products/processors-and-microcontrollers/applications-processors/i.mx-applications-processors/i.mx-7-processors:IMX7-SERIES?fsrch=1&sr=1&pageNum=1

.. _i.MX 7 Solo Datasheet: https://www.nxp.com/docs/en/data-sheet/IMX7SCEC.pdf

.. _i.MX 7 Solo Reference Manual: https://www.nxp.com/webapp/Download?colCode=IMX7SRM

.. _J-Link Tools: https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack

.. _NXP iMX7D Connect CortexM4.JLinkScript: https://wiki.segger.com/images/8/86/NXP_iMX7D_Connect_CortexM4.JLinkScript

.. _Loading Code on Cortex-M4 from Linux for the i.MX 6SoloX and i.MX 7Dual/7Solo Application Processors: https://www.nxp.com/docs/en/application-note/AN5317.pdf

.. _J-Link iMX7D Instructions: https://wiki.segger.com/IMX7D

.. _Toradex Wiki: https://developer.toradex.com/knowledge-base/freertos-on-the-cortex-m4-of-a-colibri-imx7#Memory_areas