boards/atmel/sam/sam4l_ek/doc/index.rst
.. zephyr:board:: sam4l_ek
Overview
The SAM4L series embeds picoPower technology for ultra-low power consumption. Combined power control techniques are used to bring active current consumption down to 90μA/MHz. The device allows a wide range of configurations giving the user the ability to balance between the lowest possible power consumption and the feature set selected for the application. The WAIT and RETENTION modes provide full logic and RAM retention, associated with fast wake-up capability (<1.5μs) and a very low consumption of, respectively, 3 μA and 1.5 μA. In addition, WAIT mode supports SleepWalking features. In BACKUP mode, CPU, peripherals and RAM are powered off consuming less than 0.9μA with external interrupt wake-up support.
The SAM4L-EK is a full featured design to develop for Atmel SAM4L SoC series.
The kit is equipped with a rich set of peripherals that make the ATSAM4L-EK a
perfect evaluation platform. Download the SAM4L-EK Online User Guide_ for
more details.
Hardware
ATSAM4LC4C ARM Cortex-M4 Processor
12 MHz crystal oscillator
32.768 kHz crystal oscillator
1 Micro-AB USB OTG host/device
1 AT86RF2xx IEEE 802.15.4 transceiver connector
1 RS-485 full duplex interface
1 Sensor Xplained board connector
1 Audio Jack connector 3.5mm
1 Dedicated Board Monitor MCU
1 40x4 LCD Segment Display
1 user touch button and One user pushbutton
1 user LED
1 QTouch Slider
1 QTouch Button
1 TEMT6000 Light Sensor
1 AT25DF641A Serial NOR Flash
.. zephyr:board-supported-hw::
The SAM4L-EK Design Documentation_ has detailed information about board
connections. Download the SAM4L-EK Design Documentation_ for more details.
The SAM4L MCU is configured to use the 12 MHz internal oscillator on the board with the on-chip PLL to generate an 48 MHz system clock.
The ATSAM4LC4C MCU has 4 USARTs. One of the USARTs (USART2) is connected on the embedded debug unit and can works as a console. The USART0 is shared between all others headers and RS-485 port.
Programming and Debugging
.. zephyr:board-supported-runners::
The SAM4L-EK board have a Segger Embedded Debugger Unit
J-Link OB <https://www.segger.com/jlink-ob.html>_. This provides a debug
interface to the SAM4LC4C chip. You can use Ozone or JLink to communicate with
the SAM4LC4C.
#. Download JLink from the Segger JLink Downloads Page_. Go to the section
"J-Link Software and Documentation Pack" and install the "J-Link Software
and Documentation pack for Linux". The application JLinkExe needs to be
accessible from your path.
#. Run your favorite terminal program to listen for output. Under Linux the
terminal should be :code:/dev/ttyACM0. For example:
.. code-block:: console
$ minicom -D /dev/ttyACM0 -o
The -o option tells minicom not to send the modem initialization string. Connection should be configured as follows:
#. Connect the SAM4L-EK board to your host computer using the USB debug port.
Then build and flash the :zephyr:code-sample:hello_world application.
.. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: sam4l_ek :goals: build flash
You should see "Hello World! sam4l_ek" in your terminal.
You can debug an application in the usual way. Here is an example for the
:zephyr:code-sample:hello_world application.
.. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: sam4l_ek :maybe-skip-config: :goals: debug
References
.. target-notes::
.. _SAM4L-EK Online User Guide: http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-42026-ATSAM4L-EK-User-Guide_ApplicationNote_AVR32850.pdf
.. _SAM4L-EK Design Documentation: http://ww1.microchip.com/downloads/en/DeviceDoc/doc42027_SAM4L-EK_Design_Documentation.PDF
.. _JLink Downloads Page: https://www.segger.com/downloads/jlink