{{< highlight yaml >}} apiVersion: v1alpha1 kind: BondConfig name: bond.int # Name of the bond link (interface) to be created.

Names of the links (interfaces) on which the bond will be created.

links: - enp1s2 - enp1s2 bondMode: 802.3ad # Bond mode. miimon: 100 # Link monitoring frequency in milliseconds. updelay: 200 # The time, in milliseconds, to wait before enabling a slave after a link recovery has been detected. downdelay: 200 # The time, in milliseconds, to wait before disabling a slave after a link failure has been detected. xmitHashPolicy: layer3+4 # Selects the transmit hash policy to use for slave selection. lacpRate: slow # LACPDU frames periodic transmission rate. adActorSysPrio: 65535 # Actor system priority for 802.3ad. resendIGMP: 1 # The number of times IGMP packets should be resent. packetsPerSlave: 1 # The number of packets to transmit through a slave before moving to the next one.

Configure addresses to be statically assigned to the link.

addresses: - address: 10.15.0.3/16 # IP address to be assigned to the link.

Configure routes to be statically created via the link.

routes: - destination: 10.0.0.0/8 # The route's destination as an address prefix. gateway: 10.15.0.1 # The route's gateway (if empty, creates link scope route).

# Override the hardware (MAC) address of the link.

hardwareAddr: 2e:3c:4d:5e:6f:70

# ARP link monitoring frequency in milliseconds.

arpInterval: 1000

# The list of IPv4 addresses to use for ARP link monitoring when arpInterval is set.

arpIpTargets:

- 10.15.0.1

# The list of IPv6 addresses to use for NS link monitoring when arpInterval is set.

nsIp6Targets:

- fd00::1

# Specifies whether or not ARP probes and replies should be validated.

arpValidate: active

# Specifies whether ARP probes should be sent to any or all targets.

arpAllTargets: all

# Specifies whether active-backup mode should set all slaves to the same MAC address

failOverMac: active

# Aggregate selection policy for 802.3ad.

adSelect: stable

# Whether to send LACPDU frames periodically.

adLACPActive: on

# Policy under which the primary slave should be reselected.

primaryReselect: always

# Whether dynamic shuffling of flows is enabled in tlb or alb mode.

tlbLogicalLb: 1

{{< /highlight >}}

- enp0s3
- enp0s8

{{< /highlight >}}</details> | | |bondMode |BondMode |Bond mode. <details><summary>Show example(s)</summary>{{< highlight yaml >}} bondMode: 802.3ad {{< /highlight >}}</details> |balance-rr active-backup balance-xor broadcast 802.3ad balance-tlb balance-alb | |miimon |uint32 |Link monitoring frequency in milliseconds. <details><summary>Show example(s)</summary>{{< highlight yaml >}} miimon: 200 {{< /highlight >}}</details> | | |updelay |uint32 |The time, in milliseconds, to wait before enabling a slave after a link recovery has been detected. <details><summary>Show example(s)</summary>{{< highlight yaml >}} updelay: 300 {{< /highlight >}}</details> | | |downdelay |uint32 |The time, in milliseconds, to wait before disabling a slave after a link failure has been detected. <details><summary>Show example(s)</summary>{{< highlight yaml >}} downdelay: 100 {{< /highlight >}}</details> | | |useCarrier |bool |Specifies whether or not miimon should use MII or ETHTOOL. | | |xmitHashPolicy |BondXmitHashPolicy |Selects the transmit hash policy to use for slave selection. <details><summary>Show example(s)</summary>{{< highlight yaml >}} xmitHashPolicy: layer2 {{< /highlight >}}</details> |layer2 layer3+4 layer2+3 encap2+3 encap3+4 | |arpInterval |uint32 |ARP link monitoring frequency in milliseconds. <details><summary>Show example(s)</summary>{{< highlight yaml >}} arpInterval: 1000 {{< /highlight >}}</details> | | |arpIpTargets |[]Addr |The list of IPv4 addresses to use for ARP link monitoring when arpInterval is set. Maximum of 16 targets are supported. <details><summary>Show example(s)</summary>{{< highlight yaml >}} arpIpTargets: - 10.15.0.1 {{< /highlight >}}</details> | | |nsIp6Targets |[]Addr |The list of IPv6 addresses to use for NS link monitoring when arpInterval is set. Maximum of 16 targets are supported. <details><summary>Show example(s)</summary>{{< highlight yaml >}} nsIp6Targets: - fd00::1 {{< /highlight >}}</details> | | |arpValidate |ARPValidate |Specifies whether or not ARP probes and replies should be validated. <details><summary>Show example(s)</summary>{{< highlight yaml >}} arpValidate: active {{< /highlight >}}</details> |none active backup all filter filter-active filter-backup | |arpAllTargets |ARPAllTargets |Specifies whether ARP probes should be sent to any or all targets. <details><summary>Show example(s)</summary>{{< highlight yaml >}} arpAllTargets: all {{< /highlight >}}</details> |any all | |lacpRate |LACPRate |LACPDU frames periodic transmission rate. <details><summary>Show example(s)</summary>{{< highlight yaml >}} lacpRate: fast {{< /highlight >}}</details> |slow fast | |failOverMac |FailOverMAC |Specifies whether active-backup mode should set all slaves to the same MAC address at enslavement, when enabled, or perform special handling. <details><summary>Show example(s)</summary>{{< highlight yaml >}} failOverMac: active {{< /highlight >}}</details> |none active follow | |adSelect |ADSelect |Aggregate selection policy for 802.3ad. <details><summary>Show example(s)</summary>{{< highlight yaml >}} adSelect: stable {{< /highlight >}}</details> |stable bandwidth count | |adActorSysPrio |uint16 |Actor system priority for 802.3ad. <details><summary>Show example(s)</summary>{{< highlight yaml >}} adActorSysPrio: 65535 {{< /highlight >}}</details> | | |adUserPortKey |uint16 |User port key (upper 10 bits) for 802.3ad. <details><summary>Show example(s)</summary>{{< highlight yaml >}} adUserPortKey: 0 {{< /highlight >}}</details> | | |adLACPActive |ADLACPActive |Whether to send LACPDU frames periodically. <details><summary>Show example(s)</summary>{{< highlight yaml >}} adLACPActive: on {{< /highlight >}}</details> |on off | |primaryReselect |PrimaryReselect |Policy under which the primary slave should be reselected. <details><summary>Show example(s)</summary>{{< highlight yaml >}} primaryReselect: always {{< /highlight >}}</details> |always better failure | |resendIGMP |uint32 |The number of times IGMP packets should be resent. | | |minLinks |uint32 |The minimum number of active links required for the bond to be considered active. | | |lpInterval |uint32 |The number of seconds between instances where the bonding driver sends learning packets to each slave's peer switch. | | |packetsPerSlave |uint32 |The number of packets to transmit through a slave before moving to the next one. | | |numPeerNotif |uint8 |The number of peer notifications (gratuitous ARPs and unsolicited IPv6 Neighbor Advertisements) to be issued after a failover event. | | |tlbLogicalLb |uint8 |Whether dynamic shuffling of flows is enabled in tlb or alb mode. <details><summary>Show example(s)</summary>{{< highlight yaml >}} tlbLogicalLb: 1 {{< /highlight >}}</details> | | |allSlavesActive |uint8 |Whether duplicate frames (received on inactive ports) should be dropped (0) or delivered (1). <details><summary>Show example(s)</summary>{{< highlight yaml >}} allSlavesActive: 0 {{< /highlight >}}</details> | | |peerNotifDelay |uint32 |The delay, in milliseconds, between each peer notification. | | |missedMax |uint8 |The number of arpInterval monitor checks that must fail in order for an interface to be marked down by the ARP monitor. | | |up |bool |Bring the link up or down.

If not specified, the link will be brought up. | | |mtu |uint32 |Configure LinkMTU (Maximum Transmission Unit) for the link.

If not specified, the system default LinkMTU will be used (usually 1500). | | |addresses |<a href="#BondConfig.addresses.">[]AddressConfig</a> |Configure addresses to be statically assigned to the link. | | |routes |<a href="#BondConfig.routes.">[]RouteConfig</a> |Configure routes to be statically created via the link. | | |multicast |bool |Set the multicast capability of the link. | |

addresses[] {#BondConfig.addresses.}

AddressConfig represents a network address configuration.

This field must include the network prefix length (e.g. /24 for IPv4, /64 for IPv6). <details><summary>Show example(s)</summary>{{< highlight yaml >}} address: 192.168.1.100/24 {{< /highlight >}}{{< highlight yaml >}} address: fd00::1/64 {{< /highlight >}}</details> | | |routePriority |uint32 |Configure the route priority (metric) for routes created for this address.

If not specified, the system default route priority will be used. | |

routes[] {#BondConfig.routes.}

RouteConfig represents a network route configuration.

If not specified, a default route will be created for the address family of the gateway. <details><summary>Show example(s)</summary>{{< highlight yaml >}} destination: 10.0.0.0/8 {{< /highlight >}}</details> | | |gateway |Addr |The route's gateway (if empty, creates link scope route). <details><summary>Show example(s)</summary>{{< highlight yaml >}} gateway: 10.0.0.1 {{< /highlight >}}</details> | | |source |Addr |The route's source address (optional). | | |metric |uint32 |The optional metric for the route. | | |mtu |uint32 |The optional MTU for the route. | | |table |RoutingTable |The routing table to use for the route.

If not specified, the main routing table will be used. | |