Doc Esp32h2.Doc

@defgroup cpu_esp32_esp32h2 ESP32-H2 family @ingroup cpu_esp32 @brief Specific properties of ESP32-H2 variant (family) @author Gunar Schorcht [email protected]

\section esp32_riot_esp32h2 Specific properties of ESP32-H2 variant (family)

GPIO pins {#esp32_gpio_pins_esp32h2}

ESP32-H2 has 19 broken-out GPIO pins, where a subset can be used as ADC channel and as low-power digital inputs/outputs in deep-sleep mode, the so-called LP GPIOs. Some of them are used by special SoC components. The following table gives a short overview.

<b>ADC:</b> these pins can be used as ADC inputs

<b>LP:</b> these pins are LP GPIOs and can be used in deep-sleep mode

<b>PU/PD:</b> these pins have software configurable pull-up/pull-down functionality.

GPIO2, GPIO3, GPIO8 and GPIO9 are bootstrapping pins which are used to boot ESP32-H2 in different modes:

Other combinations are invalid.

ADC Channels {#esp32_adc_channels_esp32h2}

ESP32-H2 integrates one 12-bit ADC with 5 channels in total: GPIO1, GPIO2, GPIO3, GPIO4 and GPIO5

The maximum number of ADC channels #ADC_NUMOF_MAX is 5.

I2C Interfaces {#esp32_i2c_interfaces_esp32h2}

ESP32-H2 has two built-in I2C interfaces.

The following table shows the default configuration of I2C interfaces used for ESP32-H2 boards. It can be overridden by application-specific configurations.

PWM Channels {#esp32_pwm_channels_esp32h2}

The ESP32-H2 LEDC module has 1 channel groups with 6 channels. Each of these channels can be clocked by one of the 4 timers.

SPI Interfaces {#esp32_spi_interfaces_esp32h2}

ESP32-H2 has three SPI controllers where SPI0 and SPI1 share the same bus. They are used as interface for external memory and can only operate in memory mode:

• Controller SPI0 is reserved for caching external memory like Flash
• Controller SPI1 is reserved for external memory like PSRAM
• Controller SPI2 can be used as general purpose SPI (also called FSPI)

Thus, only SPI2 (FSPI) can be used as general purpose SPI in RIOT as SPI_DEV(0).

The following table shows the pin configuration used for most boards, even though it can vary from board to board.

Timers {#esp32_timers_esp32h2}

ESP32-H2 has two timer groups with one timer each, resulting in a total of two timers. Thus one timer with one channel can be used in RIOT as timer device TIMER_DEV(0), because one timer is used as system timer.

ESP32-H2 do not have CCOMPARE registers. The counter implementation can not be used.

UART Interfaces {#esp32_uart_interfaces_esp32h2}

ESP32-H2 integrates two UART interfaces. The following default pin configuration of UART interfaces as used by a most boards can be overridden by the application, see section [Application-Specific Configurations] (#esp32_application_specific_configurations).

JTAG Interface {#esp32_jtag_interface_esp32h2}

There are two options on how to use the JTAG interface on ESP32-H2:

1. Using the built-in USB-to-JTAG bridge connected to an USB cable as follows:

   <center> USB Signal | ESP32-H2 Pin :--------------|:----------- D- (white) | GPIO26 D+ (green) | GPIO27 V_Bus (red) | 5V Ground (black) | GND </center>

2. Using an external JTAG adapter connected to the JTAG interface exposed to GPIOs as follows:

   <center> JTAG Signal | ESP32-H2 Pin :-----------|:----------- TRST_N | CHIP_PU TDO | GPIO3 (MTDO) TDI | GPIO5 (MTDI) TCK | GPIO4 (MTCK) TMS | GPIO2 (MTMS) GND | GND </center>

   @note This option requires that the USB D- and USB D+ signals are connected to the ESP32-H2 USB interface at GPIO18 and GPIO19.

Using the built-in USB-to-JTAG bridge is the default option, i.e. the JTAG interface of the ESP32-H2 is connected to the built-in USB-to-JTAG bridge. To use an external JTAG adapter, the JTAG interface of the ESP32-H2 has to be connected to the GPIOs as shown above. For this purpose eFuses have to be burned with the following command:

espefuse.py burn_efuse JTAG_SEL_ENABLE --port /dev/ttyUSB0

Once the eFuses are burned with this command and option JTAG_SEL_ENABLE, GPIO25 is used as a bootstrapping pin to choose between the two options. If GPIO25 is HIGH when ESP32-H2 is reset, the JTAG interface is connected to the built-in USB to JTAG bridge and the USB cable can be used for on-chip debugging. Otherwise, the JTAG interface is exposed to GPIO2 ... GPIO5 and an external JTAG adapter has to be used.

Alternatively, the integrated USB-to-JTAG bridge can be permanently disabled with the following command:

espefuse.py burn_efuse DIS_USB_JTAG --port /dev/ttyUSB0

Once the eFuses are burned with this command and option DIS_USB_JTAG, the JTAG interface is always exposed to GPIO2 ... GPIO5 and an external JTAG adapter has to be used.

@note Burning eFuses is an irreversible operation.

For more information about JTAG configuration for ESP32-H2, refer to the section [Configure Other JTAG Interface] (https://docs.espressif.com/projects/esp-idf/en/latest/esp32h2/api-guides/jtag-debugging/configure-other-jtag.html) in the ESP-IDF documentation.