SNLED27351 Driver {#snled27351-driver}

I²C 16x12 LED matrix driver by Sonix. Supports a maximum of four drivers, each controlling up to 192 single-color LEDs, or 64 RGB LEDs.

A slightly modified version of this IC is also known as "CKLED2001".

SNLED27351 Datasheet

Usage {#usage}

The SNLED27351 driver code is automatically included if you are using the LED Matrix or RGB Matrix feature with the snled27351 driver set, and you would use those APIs instead.

However, if you need to use the driver standalone, add this to your rules.mk:

COMMON_VPATH += $(DRIVER_PATH)/led
SRC += snled27351-mono.c # For single-color
SRC += snled27351.c # For RGB
I2C_DRIVER_REQUIRED = yes

Basic Configuration {#basic-configuration}

Add the following to your config.h:

I²C Addressing {#i2c-addressing}

The SNLED27351 has four possible 7-bit I²C addresses, depending on how the ADDR pin is connected.

To configure this, set the SNLED27351_I2C_ADDRESS_n defines to one of the following in your config.h, where n denotes the driver index:

ARM/ChibiOS Configuration {#arm-configuration}

Depending on the ChibiOS board configuration, you may need to enable and configure I²C at the keyboard level.

LED Mapping {#led-mapping}

In order to use this driver, each output must be mapped to an LED index, by adding the following to your <keyboard>.c:

const snled27351_led_t PROGMEM g_snled27351_leds[SNLED27351_LED_COUNT] = {
/* Driver
 *   |  R         G         B */
    {0, CB1_CA1,  CB1_CA2,  CB1_CA3},
    // etc...
};

In this example, the red, green and blue channels for the first LED index on driver 0 all have their cathodes connected to the CB1 pin, and their anodes on the CA1, CA2 and CA3 pins respectively.

For the single-color driver, the principle is the same, but there is only one channel:

const snled27351_led_t PROGMEM g_snled27351_leds[SNLED27351_LED_COUNT] = {
/* Driver
 *   |  V */
    {0, CB1_CA1},
    // etc...
};

These values correspond to the register indices as shown in the datasheet on page 13.

API {#api}

struct snled27351_led_t {#api-snled27351-led-t}

Contains the PWM register addresses for a single RGB LED.

Members {#api-snled27351-led-t-members}

• uint8_t driver
  The driver index of the LED, from 0 to 3.
• uint8_t r
  The output PWM register address for the LED's red channel (RGB driver only).
• uint8_t g
  The output PWM register address for the LED's green channel (RGB driver only).
• uint8_t b
  The output PWM register address for the LED's blue channel (RGB driver only).
• uint8_t v
  The output PWM register address for the LED (single-color driver only).

void snled27351_init(uint8_t index) {#api-snled27351-init}

Initialize the LED driver. This function should be called first.

Arguments {#api-snled27351-init-arguments}

• uint8_t index
  The driver index.

void snled27351_write_register(uint8_t index, uint8_t reg, uint8_t data) {#api-snled27351-write-register}

Set the value of the given register.

Arguments {#api-snled27351-write-register-arguments}

• uint8_t index
  The driver index.
• uint8_t reg
  The register address.
• uint8_t data
  The value to set.

void snled27351_select_page(uint8_t index, uint8_t page) {#api-snled27351-select-page}

Change the current page for configuring the LED driver.

Arguments {#api-snled27351-select-page-arguments}

• uint8_t index
  The driver index.
• uint8_t page
  The page number to select.

void snled27351_set_color(int index, uint8_t red, uint8_t green, uint8_t blue) {#api-snled27351-set-color}

Set the color of a single LED (RGB driver only). This function does not immediately update the LEDs; call snled27351_update_pwm_buffers() after you are finished.

Arguments {#api-snled27351-set-color-arguments}

• int index
  The LED index (ie. the index into the g_snled27351_leds array).
• uint8_t red
  The red value to set.
• uint8_t green
  The green value to set.
• uint8_t blue
  The blue value to set.

void snled27351_set_color_all(uint8_t red, uint8_t green, uint8_t blue) {#api-snled27351-set-color-all}

Set the color of all LEDs (RGB driver only).

Arguments {#api-snled27351-set-color-all-arguments}

• uint8_t red
  The red value to set.
• uint8_t green
  The green value to set.
• uint8_t blue
  The blue value to set.

void snled27351_set_value(int index, uint8_t value) {#api-snled27351-set-value}

Set the brightness of a single LED (single-color driver only). This function does not immediately update the LEDs; call snled27351_update_pwm_buffers() after you are finished.

Arguments {#api-snled27351-set-value-arguments}

• int index
  The LED index (ie. the index into the g_snled27351_leds array).
• uint8_t value
  The brightness value to set.

void snled27351_set_value_all(uint8_t value) {#api-snled27351-set-value-all}

Set the brightness of all LEDs (single-color driver only).

Arguments {#api-snled27351-set-value-all-arguments}

• uint8_t value
  The brightness value to set.

void snled27351_set_led_control_register(uint8_t index, bool red, bool green, bool blue) {#api-snled27351-set-led-control-register-rgb}

Configure the LED control registers for a single LED (RGB driver only). This function does not immediately update the LEDs; call snled27351_update_led_control_registers() after you are finished.

Arguments {#api-snled27351-set-led-control-register-rgb-arguments}

• uint8_t index
  The LED index (ie. the index into the g_snled27351_leds array).
• bool red
  Enable or disable the red channel.
• bool green
  Enable or disable the green channel.
• bool blue
  Enable or disable the blue channel.

void snled27351_set_led_control_register(uint8_t index, bool value) {#api-snled27351-set-led-control-register-mono}

Configure the LED control registers for a single LED (single-color driver only). This function does not immediately update the LEDs; call snled27351_update_led_control_registers() after you are finished.

Arguments {#api-snled27351-set-led-control-register-mono-arguments}

• uint8_t index
  The LED index (ie. the index into the g_snled27351_leds array).
• bool value
  Enable or disable the LED.

void snled27351_update_pwm_buffers(uint8_t index) {#api-snled27351-update-pwm-buffers}

Flush the PWM values to the LED driver.

Arguments {#api-snled27351-update-pwm-buffers-arguments}

• uint8_t index
  The driver index.

void snled27351_update_led_control_registers(uint8_t index) {#api-snled27351-update-led-control-registers}

Flush the LED control register values to the LED driver.

Arguments {#api-snled27351-update-led-control-registers-arguments}

• uint8_t index
  The driver index.