NXP i.MX 8M Plus and i.MX 8M Mini Evaluation Kits (imx8mp-evk, imx8mm-evk)

The imx8mp-evk and imx8mm-evk machine models the i.MX 8M Plus and i.MX 8M Mini Evaluation Kits, based on i.MX 8M Plus and i.MX8M Mini SoCs.

Supported devices

The imx8mp-evk and imx8mm-evk machines implement the following devices:

• Up to 4 Cortex-A53 cores
• Generic Interrupt Controller (GICv3)
• 4 UARTs
• 3 USDHC Storage Controllers
• 1 Designware PCI Express Controller
• 1 Ethernet Controller
• 2 Designware USB 3 Controllers
• 2 FlexCAN 3 CAN Controllers (imx8mp-evk only)
• 5 GPIO Controllers
• 6 I2C Controllers
• 3 SPI Controllers
• 3 Watchdogs
• 6 General Purpose Timers
• Secure Non-Volatile Storage (SNVS) including an RTC
• Clock Tree

Boot options

The imx8mp-evk and imx8mm-evk machines can start a Linux kernel directly using the standard -kernel functionality.

Direct Linux Kernel Boot ''''''''''''''''''''''''

Probably the easiest way to get started with a whole Linux system on the machine is to generate an image with Buildroot. Version 2024.11.1 is tested at the time of writing and involves two steps. First run the following commands in the toplevel directory of the Buildroot source tree:

For i.MX 8M Plus EVK:

.. code-block:: bash

$ make freescale_imx8mpevk_defconfig $ make

For i.MX 8M Mini EVK:

.. code-block:: bash

$ make freescale_imx8mmevk_defconfig $ make

Once finished successfully there is an output/image subfolder. Navigate into it and resize the SD card image to a power of two:

.. code-block:: bash

$ qemu-img resize sdcard.img 256M

Now that everything is prepared the machine can be started as follows:

For i.MX 8M Plus EVK:

.. code-block:: bash

$ qemu-system-aarch64 -M imx8mp-evk
-display none -serial null -serial stdio
-kernel Image
-dtb imx8mp-evk.dtb
-append "root=/dev/mmcblk2p2"
-drive file=sdcard.img,if=sd,bus=2,format=raw,id=mmcblk2

For i.MX 8M Mini EVK:

.. code-block:: bash

$ qemu-system-aarch64 -M imx8mm-evk -smp 4 -m 2G
-display none -serial null -serial stdio
-kernel Image
-dtb imx8mm-evk.dtb
-append "root=/dev/mmcblk2p2"
-drive file=sdcard.img,if=sd,bus=2,format=raw,id=mmcblk2

KVM Acceleration

To enable hardware-assisted acceleration via KVM, append -accel kvm to the command line. While this speeds up performance significantly, be aware of the following limitations:

• The imx8mp-evk and imx8mm-evk machines are not included under the "virtualization use case" of :doc:QEMU's security policy . This means that you should not trust that it can contain malicious guests, whether it is run using TCG or KVM. If you don't trust your guests and you're relying on QEMU to be the security boundary, you want to choose another machine such as virt.
• Rather than Cortex-A53 CPUs, the same CPU type as the host's will be used. This is a limitation of KVM and may not work with guests with a tight dependency on Cortex-A53.
• No EL2 and EL3 exception levels are available which is also a KVM limitation. Direct kernel boot should work but running U-Boot, TF-A, etc. won't succeed.