Documentation/driver-api/scsi.rst
:Author: James Bottomley :Author: Rob Landley
Once upon a time, the Small Computer Systems Interface defined both a parallel I/O bus and a data protocol to connect a wide variety of peripherals (disk drives, tape drives, modems, printers, scanners, optical drives, test equipment, and medical devices) to a host computer.
Although the old parallel (fast/wide/ultra) SCSI bus has largely fallen out of use, the SCSI command set is more widely used than ever to communicate with devices over a number of different buses.
The SCSI protocol <https://www.t10.org/scsi-3.htm>__ is a big-endian
peer-to-peer packet based protocol. SCSI commands are 6, 10, 12, or 16
bytes long, often followed by an associated data payload.
SCSI commands can be transported over just about any kind of bus, and
are the default protocol for storage devices attached to USB, SATA, SAS,
Fibre Channel, FireWire, and ATAPI devices. SCSI packets are also
commonly exchanged over Infiniband,
TCP/IP (iSCSI <https://en.wikipedia.org/wiki/ISCSI>), even Parallel ports <http://cyberelk.net/tim/parport/parscsi.html>.
The SCSI subsystem uses a three layer design, with upper, mid, and low layers. Every operation involving the SCSI subsystem (such as reading a sector from a disk) uses one driver at each of the 3 levels: one upper layer driver, one lower layer driver, and the SCSI midlayer.
The SCSI upper layer provides the interface between userspace and the kernel, in the form of block and char device nodes for I/O and ioctl(). The SCSI lower layer contains drivers for specific hardware devices.
In between is the SCSI mid-layer, analogous to a network routing layer such as the IPv4 stack. The SCSI mid-layer routes a packet based data protocol between the upper layer's /dev nodes and the corresponding devices in the lower layer. It manages command queues, provides error handling and power management functions, and responds to ioctl() requests.
The upper layer supports the user-kernel interface by providing device nodes.
sd (sd_mod.o)
sr (sr_mod.o)
st (st.o)
sg (sg.o)
ch (ch.c)
include/scsi/scsi_device.h
.. kernel-doc:: include/scsi/scsi_device.h
:internal:
drivers/scsi/scsi.c
~~~~~~~~~~~~~~~~~~~
Main file for the SCSI midlayer.
.. kernel-doc:: drivers/scsi/scsi.c
:export:
drivers/scsi/scsicam.c
~~~~~~~~~~~~~~~~~~~~~~
`SCSI Common Access
Method <http://www.t10.org/ftp/t10/drafts/cam/cam-r12b.pdf>`__ support
functions, for use with HDIO_GETGEO, etc.
.. kernel-doc:: drivers/scsi/scsicam.c
:export:
drivers/scsi/scsi_error.c
~~~~~~~~~~~~~~~~~~~~~~~~~~
Common SCSI error/timeout handling routines.
.. kernel-doc:: drivers/scsi/scsi_error.c
:export:
drivers/scsi/scsi_devinfo.c
Manage scsi_dev_info_list, which tracks blacklisted and whitelisted devices.
.. kernel-doc:: drivers/scsi/scsi_devinfo.c :export:
drivers/scsi/scsi_ioctl.c
Handle ioctl() calls for SCSI devices.
.. kernel-doc:: drivers/scsi/scsi_ioctl.c
:export:
drivers/scsi/scsi_lib.c
~~~~~~~~~~~~~~~~~~~~~~~~
SCSI queuing library.
.. kernel-doc:: drivers/scsi/scsi_lib.c
:export:
drivers/scsi/scsi_lib_dma.c
SCSI library functions depending on DMA (map and unmap scatter-gather lists).
.. kernel-doc:: drivers/scsi/scsi_lib_dma.c :export:
drivers/scsi/scsi_proc.c
The functions in this file provide an interface between the PROC file
system and the SCSI device drivers It is mainly used for debugging,
statistics and to pass information directly to the lowlevel driver. I.E.
plumbing to manage /proc/scsi/\*
.. kernel-doc:: drivers/scsi/scsi_proc.c
drivers/scsi/scsi_netlink.c
Infrastructure to provide async events from transports to userspace via
netlink, using a single NETLINK_SCSITRANSPORT protocol for all
transports. See the original patch submission <https://lore.kernel.org/linux-scsi/[email protected]/>__
for more details.
.. kernel-doc:: drivers/scsi/scsi_netlink.c :internal:
drivers/scsi/scsi_scan.c
Scan a host to determine which (if any) devices are attached. The
general scanning/probing algorithm is as follows, exceptions are made to
it depending on device specific flags, compilation options, and global
variable (boot or module load time) settings. A specific LUN is scanned
via an INQUIRY command; if the LUN has a device attached, a scsi_device
is allocated and setup for it. For every id of every channel on the
given host, start by scanning LUN 0. Skip hosts that don't respond at
all to a scan of LUN 0. Otherwise, if LUN 0 has a device attached,
allocate and setup a scsi_device for it. If target is SCSI-3 or up,
issue a REPORT LUN, and scan all of the LUNs returned by the REPORT LUN;
else, sequentially scan LUNs up until some maximum is reached, or a LUN
is seen that cannot have a device attached to it.
.. kernel-doc:: drivers/scsi/scsi_scan.c
:export:
drivers/scsi/scsi_sysctl.c
Set up the sysctl entry: "/dev/scsi/logging_level" (DEV_SCSI_LOGGING_LEVEL) which sets/returns scsi_logging_level.
drivers/scsi/scsi_sysfs.c
SCSI sysfs interface routines.
.. kernel-doc:: drivers/scsi/scsi_sysfs.c
:export:
drivers/scsi/hosts.c
~~~~~~~~~~~~~~~~~~~~
mid to lowlevel SCSI driver interface
.. kernel-doc:: drivers/scsi/hosts.c
:export:
drivers/scsi/scsi_common.c
general support functions
.. kernel-doc:: drivers/scsi/scsi_common.c :export:
Transport classes are service libraries for drivers in the SCSI lower layer, which expose transport attributes in sysfs.
Fibre Channel transport
The file drivers/scsi/scsi_transport_fc.c defines transport attributes
for Fibre Channel.
.. kernel-doc:: drivers/scsi/scsi_transport_fc.c
:export:
iSCSI transport class
~~~~~~~~~~~~~~~~~~~~~
The file drivers/scsi/scsi_transport_iscsi.c defines transport
attributes for the iSCSI class, which sends SCSI packets over TCP/IP
connections.
.. kernel-doc:: drivers/scsi/scsi_transport_iscsi.c
:export:
Serial Attached SCSI (SAS) transport class
The file drivers/scsi/scsi_transport_sas.c defines transport attributes for Serial Attached SCSI, a variant of SATA aimed at large high-end systems.
The SAS transport class contains common code to deal with SAS HBAs, an approximated representation of SAS topologies in the driver model, and various sysfs attributes to expose these topologies and management interfaces to userspace.
In addition to the basic SCSI core objects this transport class introduces two additional intermediate objects: The SAS PHY as represented by struct sas_phy defines an "outgoing" PHY on a SAS HBA or Expander, and the SAS remote PHY represented by struct sas_rphy defines an "incoming" PHY on a SAS Expander or end device. Note that this is purely a software concept, the underlying hardware for a PHY and a remote PHY is the exactly the same.
There is no concept of a SAS port in this code, users can see what PHYs form a wide port based on the port_identifier attribute, which is the same for all PHYs in a port.
.. kernel-doc:: drivers/scsi/scsi_transport_sas.c :export:
SATA transport class
The SATA transport is handled by libata, which has its own book of
documentation in this directory.
Parallel SCSI (SPI) transport class
The file drivers/scsi/scsi_transport_spi.c defines transport attributes for traditional (fast/wide/ultra) SCSI buses.
.. kernel-doc:: drivers/scsi/scsi_transport_spi.c :export:
SCSI RDMA (SRP) transport class
The file drivers/scsi/scsi_transport_srp.c defines transport
attributes for SCSI over Remote Direct Memory Access.
.. kernel-doc:: drivers/scsi/scsi_transport_srp.c
:export:
SCSI lower layer
================
Host Bus Adapter transport types
--------------------------------
Many modern device controllers use the SCSI command set as a protocol to
communicate with their devices through many different types of physical
connections.
In SCSI language a bus capable of carrying SCSI commands is called a
"transport", and a controller connecting to such a bus is called a "host
bus adapter" (HBA).
Debug transport
~~~~~~~~~~~~~~~
The file drivers/scsi/scsi_debug.c simulates a host adapter with a
variable number of disks (or disk like devices) attached, sharing a
common amount of RAM. Does a lot of checking to make sure that we are
not getting blocks mixed up, and panics the kernel if anything out of
the ordinary is seen.
To be more realistic, the simulated devices have the transport
attributes of SAS disks.
For documentation see http://sg.danny.cz/sg/scsi_debug.html
todo
~~~~
Parallel (fast/wide/ultra) SCSI, USB, SATA, SAS, Fibre Channel,
FireWire, ATAPI devices, Infiniband, Parallel ports,
netlink...